‹ Back
IUV SMART LED-UV-Trocknungssystem

IUV SMART LED-UV-Trocknungssystem

LED UV dryer with 25 W/cm² and zone control for higher web speeds: only the width that is needed is switched on.

Price on request · Individual advice & configuration by our team

Highlights & benefits

  • 25 W/cm² UV output, lamp length 10 to 200 cm
  • Zone control: only the required width is switched on
  • For higher web speeds than the ECO
  • Mercury-free and ozone-free
  • Service life of over 30,000 hours

Description & applications

Automatic web detection in the film: if the width or position of the web changes, only the LED sections above the material light up. On the right, the display on the control panel. Film from IUV, no sound.
The changeover in the film: the LED head and the mercury lamp fit into the same housing and are swapped by hand. The controller detects which insert is installed. Film from IUV, no sound.

The SMART delivers 25 W/cm² and is built for higher web speeds. The difference from the ECO lies in the output and in the finer zone control: you switch on only the zones over which material is actually running.

Technical data

  • UV output: 25 W/cm²
  • Lamp length: 10 to 200 cm
  • Wavelength: 365 nm, 385 nm or 395 nm
  • Zone control: in steps from 10 mm
  • Cooling: water cooling
  • Service life: over 30,000 hours
  • Operating temperature: below 40 °C

What zone control brings

If a narrow web runs through a wide press, a continuous head lights up across the full width. Zone control switches the sections individually. This saves up to 30 per cent in electricity. How much you save depends on how often you run below full width.

Retrofit instead of replace

An LED UV dryer can be fitted into existing printing presses. The press stays, the dryer is swapped. This is the usual route for narrow-web flexo, flexible packaging and sheetfed offset.

If you do not want to commit either way, choose the hybrid version: the LED head and the mercury lamp sit in the same housing, and you decide for each job which one to cure with. Inks and varnishes that are still formulated for mercury then continue to run as before.

How a retrofit works

  • Machine data: manufacturer and model, web or print width, number of print units, speed, current dryer
  • Quote per print unit: you receive a separate line item for each print unit, not a flat rate
  • Ink approval: together with your ink supplier, because LED-curing inks differ from those for mercury
  • Installation, training, remote support: by our technical department

How LED UV differs from mercury

LED heads contain no mercury and do not emit below 240 nm, so no ozone is produced. They switch on and off without warm-up time. Their service life is considerably longer than that of a mercury lamp: suppliers quote 10,000 to 25,000 hours for LED, while mercury lamps are usually replaced after 1,000 to 2,000 hours. For these systems, over 30,000 hours are stated.

In return, LED systems need specially matched inks and varnishes. We clarify this point with your ink supplier before the quote.

What we need for a quote

  • Press manufacturer and model
  • Print width or web width
  • Number of print units to be cured
  • Production speed
  • Which dryer is currently fitted
  • Which inks and varnishes you use
  • Whether cooling water is available

With this information, we calculate the right length and output for you. Write to us or call us on +49 9187 409707-0.

Illustrations similar. Technical data are manufacturer's specifications.

Technical data

UV output
25 W/cm²
Lamp length
10 to 200 cm
Wavelength
365 nm, 385 nm or 395 nm
Zone control
in steps from 10 mm
Cooling
Water cooling
Service life
over 30,000 hours
Operating temperature
below 40 °C

Information based on manufacturer's documentation. Subject to change in technology and design. Only the information in the respective quote is binding.

Interesse an der IUV SMART LED-UV-Trocknungssystem?

We will be happy to advise you personally, prepare a suitable quote and set up the system individually for your application, including installation, training and service.