In short: An LED UV dryer can be fitted to existing printing machines: the machine stays, the dryer is replaced. For a quote you need the machine data and your ink supplier's approval for LED-curing inks. Funding through the German federal funding programme for energy and resource efficiency in industry may be possible; the funding body decides case by case.
What happens during a retrofit
An LED UV dryer cures UV inks and UV varnishes with LED light instead of a mercury vapour lamp. In a retrofit, you install the new dryer in your existing printing press. The press stays, the dryer is replaced. This is the usual route for narrow-web flexo, flexible packaging and sheet-fed offset.
The IUV dryers that brunner supplies are mercury-free and ozone-free, switch on and off instantly and need no warm-up time. They are designed for a service life of over 30,000 hours and operate below 40 °C.
Pure LED or hybrid
If you do not want to commit, choose the hybrid version. The LED head and the mercury lamp fit into the same housing and are swapped by hand, and the controller detects which insert is fitted. You decide per job what you cure with. Inks and varnishes that are still matched to mercury then continue to run as before. The ECO is available as a pure LED system and as a hybrid.
The three models compared
| Model | UV output | Special feature |
|---|---|---|
| IUV ECO | 18 W/cm² | Entry to LED UV curing, also as a hybrid |
| IUV SMART | 25 W/cm² | for higher web speeds, zone control in steps from 10 mm |
| IUV SUPER | 25 W/cm² | like SMART, plus a modular power supply system on the CAN bus |
All three are available with lamp lengths from 10 to 200 cm, water-cooled, with wavelengths of 365 nm, 385 nm or 395 nm.
The zone control on the SMART and SUPER only switches on the sections over which material runs. If a narrow web runs through a wide machine, a continuous head lights up the full width. On the SUPER, if one fails, the remaining power supply modules take over and the faulty one is replaced individually. For businesses running multiple shifts, this is the main reason for this model.
Why businesses retrofit
An LED head switches on and off instantly, with no warm-up time. Businesses with a working printing press therefore replace the dryer and keep the machine. The dryer is mercury-free and ozone-free, and the units operate below 40 °C. You choose the illuminated length to suit the web or print width of your machine, with 10 to 200 cm available. The wavelength (365 nm, 385 nm or 395 nm) depends on the inks and varnishes you cure, and therefore belongs in the coordination with your ink supplier. We will discuss which combination suits you based on your jobs and your machine.
How a retrofit works
- Collect the machine data: manufacturer and model, web or print width, number of print units, speed and your current dryer.
- Quotation: you receive a separate line item for each print unit, not a flat rate.
- Ink approval: check with your ink supplier which inks and varnishes are LED-curing. These are different systems from those used for mercury lamps.
- Installation and training.
Funding requirements
Replacing a dryer can be eligible for funding under the Federal Funding for Energy and Resource Efficiency in the Economy. There are two routes: a grant via BAFA or a loan with a repayment subsidy via KfW (programme 295). The following requirements usually apply:
- The measure must save energy.
- An energy-saving concept is in place.
- The application is submitted before the measure begins.
This is a guide, not a commitment. The funding body decides on a case-by-case basis. Check the current conditions with BAFA or KfW before you order, and submit the application before placing the order.
What to look out for when choosing
- Inks and varnishes: You clarify the approval for LED curing with your ink supplier.
- Web speed and print width: They determine the output you need.
- Operation: If you often run below full width, zone control makes sense. In multi-shift operation, reliability matters.
- Hybrid or LED only: Hybrid keeps the option of a mercury lamp open.
Advice from brunner
You can find all models under LED UV curing. brunner has been a specialist dealer since 2007, with its own technical department in Altdorf near Nuremberg. We advise you, support the installation, train your team and supply service and spare parts.
Would you like to know what suits your case? Talk to us or request a Sample request .
Frequently asked questions
Can I retrofit an LED UV dryer to an old printing press?
Yes. The press stays, the dryer is replaced. This is common on narrow-web flexo, flexible packaging and sheetfed offset. For a quotation we need the manufacturer and model, web width, number of print units, speed and your current dryer.
Is there funding for LED UV dryers?
Possibly. Replacing a dryer can be eligible for funding under the Federal Funding for Energy and Resource Efficiency in the Economy, as a grant via BAFA or as a loan with a repayment subsidy via KfW (programme 295). The requirements are energy savings, an energy-saving concept and an application before the start. The funding body decides on a case-by-case basis.
Do I need different inks for LED UV?
Yes, LED-curing inks and varnishes are different from those for mercury lamps. Clarify the approval with your ink supplier. With the hybrid version, inks matched to mercury continue to run as well.
Which LED UV dryer do I need, ECO, SMART or SUPER?
The ECO at 18 W/cm² is the entry-level model. SMART and SUPER offer 25 W/cm² and zone control, and the SUPER also has a modular power supply system for multi-shift operation. The choice depends on web speed, print width and operation.
