In short: A label finisher, also called a label finishing machine or slitter rewinder, processes printed label rolls after printing: it unwinds the master roll, inspects the material, slits it lengthways and rewinds it into finished rolls. Depending on its specification, it also die-cuts, varnishes and weeds. Which machine suits you depends on web width, material and inspection requirements; brunner offers nine models of the BGM Elite range for this.
What a label finisher does
Behind the printing press at a label printer there is usually a wide master roll. This roll is not yet what the customer needs. A label finisher takes it, unwinds it, runs the web over an inspection section, slits it into narrow strips and rewinds the strips into rolls that run in a labelling machine. Specialists also speak of a slitter rewinder, rewinding machine, roll slitting machine or label rewinder. At its core, the task is the same: turning a print job into rolls ready for sale.
With some models, it does not stop at slitting. A finishing line varnishes, die-cuts and weeds digitally printed rolls before they are slit. One machine then replaces several operations.
Designs at a glance
All nine models that brunner offers come from the Elite range from BGM. They differ mainly in how the web is inspected, which materials they process and which web width they take.
- Inspection slitter rewinders (iSR): The web runs over an inspection table where the operator inspects it. The range includes the BGM Elite 410 iSR and the BGM Elite 450 iSR and, with 550 mm web width, the single-rewind version and the dual-rewind version with two rewind stations.
- Camera inspection (Label-i): A camera checks 100% of the labels against the master. Errors are located and can be removed. Available as BGM Elite 410 Label-i and BGM Elite 450 Label-i. The 450 works with the E+L 200 % MIS2 camera system and compares against the print master via PDF.
- Several materials: The BGM Elite 450 Multiflex processes unreinforced and reinforced films, metal foils, paper and thin board from 11 µm. It has two slitting methods, rotary shear cut and crush cut, and two rewinders. The BGM Elite 450 EcoFlex slits films, paper and board from 11 µm with six knife sets.
- Finishing and die-cutting: The BGM Elite 330 Digiflex varnishes, die-cuts, weeds and slits digitally printed rolls in a single pass.
The models compared
| Model | Web width | Speed | Special feature |
|---|---|---|---|
| Elite 410 iSR | 410 mm | up to 300 m/min | Inspection table, 230 V / 13 A |
| Elite 450 iSR | 450 mm | up to 300 m/min | Inspection table, 230 V / 13 A |
| Elite 410 Label-i | 410 mm | up to 300 m/min | Camera, 100% inspection |
| Elite 450 Label-i | 450 mm | up to 300 m/min | Camera E+L 200 % MIS2 |
| Elite 450 Multiflex | 450 mm | up to 300 m/min | Films and board from 11 µm, two rewinders |
| Elite 450 EcoFlex | 450 mm | up to 300 m/min | six knife sets, films, paper, board from 11 µm |
| Elite 550 iSR Single | 550 mm | up to 300 m/min | Unwind up to Ø 1,000 mm |
| Elite 550 iSR Dual | 550 mm | up to 300 m/min | two rewind stations |
| Elite 330 Digiflex | 330 mm | Finishing up to 160 m/min, die-cutting up to 110 m/min | Varnishing, die-cutting, weeding, slitting |
What matters when choosing
- Web width: It depends on your master rolls. The machines cover 330, 410, 450 and 550 mm.
- Material: For paper and films, an iSR or Label-i is enough. Anyone who also slits thin films, metal foils or lightweight board should look at the Multiflex or the EcoFlex.
- Inspection: At the inspection table, the operator checks by eye. The camera models compare every label with the master. This pays off where errors are costly, for example in pharma, food or cosmetics.
- Slitting pattern: The minimum slitting width is 13 mm on the iSR, Label-i and Multiflex models and 20 mm on the Digiflex. If you slit many narrow rolls from a wide one, consider the dual version with two rewind stations.
- Connection: The iSR and Label-i models 410 and 450 run on 230 V, 13 A, single-phase. The EcoFlex needs three phases plus neutral at 32 A, the Digiflex 400 to 440 V three-phase. Check early whether your installation site can supply this.
- Digital printing: If you need to varnish and die-cut digitally printed rolls, the Digiflex is the right line, because printing, die-cutting and slitting stay in register.
What brunner offers
brunner has been a specialist dealer with its own technical department since 2007. We advise you on selection, configure the machine with you for your cutting layout and materials, install it and train your staff. After that, we remain your contact for service, spare parts and consumables.
You will find the category with all models and technical data under Label finishing. For a recommendation for your production, use our Contact form. If you would like a sample on your own material, the Sample request is the right way to go.
Frequently asked questions
What is the difference between a label finisher and a slitter rewinder?
In everyday use the terms are mostly used interchangeably. A slitter rewinder slits and rewinds. A label finisher can also inspect, varnish, die-cut and strip waste matrix, depending on its configuration.
How fast does a label slitter rewinder run?
All eight slitter rewinders in the BGM Elite series at brunner run at up to 300 m/min. The Digiflex finishes at up to 160 m/min and die-cuts at up to 110 m/min.
Is camera inspection worth it compared with an inspection table?
On the Elite 410 and 450 Label-i, a camera checks 100 % of the labels against the master and stops at defects for removal. This makes sense when every label must be flawless. For less critical jobs, inspection at the inspection table of the iSR models is often enough.
Can I slit films and thin board on a label finisher?
Yes, with the BGM Elite 450 Multiflex and the BGM Elite 450 EcoFlex. Both process films, paper and board from 11 µm. The Multiflex also handles metallic foils and has two rewinders.
